Over the last few years there has been a noticeable increase in the interest in measuring the microbial contamination of the air. This stems from the awareness that airborne microorganisms have the ability to cause harmful effects on the health of individuals. The present work aims to assess the level of exposure to biological agents in work environments, especially characterized by purification plants. For the sampling of the bioaerosol an active orthogonal impact sampler was used with a head endowed with holes and adaptable to Petri dishes with a diameter of 90 mm. Air volumes were sampled at different points in each plant, searching for the following parameters: total bacterial load at 22 and 36 ° C, total fungal load, staphylococci, streptococci and gram negative bacteria. After appropriate incubation of the plates, the microorganisms were counted expressing the result as UFC (colony forming unit). To have a correlation between the charges detected and a judgment on the quality of the air, those reported in the INAIL Guidelines were chosen as reference values; in this document the index taken into consideration is the global index of microbial contamination (IGCM) on the basis of which a classification is established regarding the level of microbial pollution. Therefore, going to calculate the IGCM, obtained from the sum of the total bacterial charge at 22 and 36 ° C and of the fungal one, it was possible to determine, for each point, the corresponding contamination class. For each of the three bacterial groups, on the other hand, in addition to counting, we proceeded with the careful observation of the different types of colonies in order to isolate them in pure culture on specific soil. This step is done in order to be able to carry out the subsequent tests aimed at microbiological characterization, and especially the final identification test, with greater precision. Through a suitable software, at this point, for each isolated colony of each bacterial group, we have gone back to the corresponding species and, referring to Annex XLVI of Legislative Decree 81/08, to the number relative to the hazard class of the date species. In this way we tried to integrate the measurement of microbial contamination with the presence of species considered more or less pathogenic with the aim of giving a more complete judgment on the quality of the air of the plants, defining which are the most critical points.
Nel corso degli ultimi anni si è assistito a un notevole aumento dellinteresse per la misura della contaminazione microbica dellaria. Questo nasce dalla consapevolezza che i microrganismi aerodiffusi abbiano la capacità di causare effetti nocivi sulla salute degli individui. Il presente lavoro ha lobiettivo di valutare il livello di esposizione agli agenti biologici in ambienti di lavoro, caratterizzati specialmente da impianti di depurazione. Per il campionamento del bioaerosol è stato utilizzato un campionatore attivo ad impatto ortogonale con testata dotata di fori e adattabile a piastre Petri di diametro 90 mm. Sono stati campionati volumi daria, in diversi punti di ciascun impianto, andando a ricercare i seguenti parametri: carica batterica totale a 22 e 36 °C, carica micotica totale, stafilococchi, streptococchi e batteri Gram-negativi. Dopo opportuna incubazione delle piastre, si è proceduto con il conteggio dei microrganismi esprimendo il risultato come UFC (unità formanti colonia). Per avere una correlazione tra le cariche rilevate e un giudizio sulla qualità dellaria sono stati scelti come valori di riferimento quelli riportati nelle Linee Guida dellINAIL; in tale documento lindice preso in considerazione è lindice globale di contaminazione microbica in base al quale viene stabilita una classificazione riguardo al livello di inquinamento microbico. Perciò andando a calcolare lIGCM, ottenuto dalla somma della carica batterica totale a 22 e 36 °C e di quella micotica, si è riusciti a determinare, per ogni punto, la classe di contaminazione corrispondente. Per ognuno dei tre gruppi batterici, invece, oltre al conteggio, si è proseguito con lattenta osservazione delle diverse tipologie di colonie in modo da isolarle in coltura pura su terreno specifico. Questo passaggio viene fatto per poter svolgere, con maggiore precisione, i successivi test, finalizzati alla caratterizzazione microbiologica, e soprattutto il test finale di identificazione. Attraverso un adatto software, a questo punto, per ogni colonia isolata, di ciascun gruppo batterico, si è risaliti alla specie corrispondente e, facendo riferimento allAllegato XLVI del D.Lgs 81/08, al numero relativo alla classe di pericolosità della data specie. In questo modo si è cercato di integrare la misura della contaminazione microbica con la presenza di specie considerate più o meno patogene con lo scopo di dare un giudizio più completo sulla qualità dellaria degli impianti definendo quali sono i punti più critici.
Il rischio biologico negli ambienti di lavoro. Studio sulle condizioni di presenza microbica in impianti di depurazione.
GUASCO, FEDERICA
2018/2019
Abstract
Over the last few years there has been a noticeable increase in the interest in measuring the microbial contamination of the air. This stems from the awareness that airborne microorganisms have the ability to cause harmful effects on the health of individuals. The present work aims to assess the level of exposure to biological agents in work environments, especially characterized by purification plants. For the sampling of the bioaerosol an active orthogonal impact sampler was used with a head endowed with holes and adaptable to Petri dishes with a diameter of 90 mm. Air volumes were sampled at different points in each plant, searching for the following parameters: total bacterial load at 22 and 36 ° C, total fungal load, staphylococci, streptococci and gram negative bacteria. After appropriate incubation of the plates, the microorganisms were counted expressing the result as UFC (colony forming unit). To have a correlation between the charges detected and a judgment on the quality of the air, those reported in the INAIL Guidelines were chosen as reference values; in this document the index taken into consideration is the global index of microbial contamination (IGCM) on the basis of which a classification is established regarding the level of microbial pollution. Therefore, going to calculate the IGCM, obtained from the sum of the total bacterial charge at 22 and 36 ° C and of the fungal one, it was possible to determine, for each point, the corresponding contamination class. For each of the three bacterial groups, on the other hand, in addition to counting, we proceeded with the careful observation of the different types of colonies in order to isolate them in pure culture on specific soil. This step is done in order to be able to carry out the subsequent tests aimed at microbiological characterization, and especially the final identification test, with greater precision. Through a suitable software, at this point, for each isolated colony of each bacterial group, we have gone back to the corresponding species and, referring to Annex XLVI of Legislative Decree 81/08, to the number relative to the hazard class of the date species. In this way we tried to integrate the measurement of microbial contamination with the presence of species considered more or less pathogenic with the aim of giving a more complete judgment on the quality of the air of the plants, defining which are the most critical points.È consentito all'utente scaricare e condividere i documenti disponibili a testo pieno in UNITESI UNIPV nel rispetto della licenza Creative Commons del tipo CC BY NC ND.
Per maggiori informazioni e per verifiche sull'eventuale disponibilità del file scrivere a: unitesi@unipv.it.
https://hdl.handle.net/20.500.14239/23436